Best brake calipers for motorcycles

It’s easy to repair brake calipers on motorcycles, but you should always follow the manual to do the job properly. Before doing any repairs, read the instruction manual carefully, and make sure to take your time. It is important not to rush through the repair process. In some cases, you may have to replace the entire braking system. It is also important to note that some motorcycles use different piston sizes and should only be repaired by a qualified mechanic.

To replace the calipers, you must check the model of the motorcycle. You can easily spot the right model by looking at the brakes of other motorcycles. If the calipers are damaged or have been removed from the bike, you should replace them. However, it is not necessary to change the rotor or the front drum. Just make sure to check the brakes of the bike before replacing them. Moreover, you should also replace the master cylinder.

Aside from replacing the calipers, you should also replace the brake lines. You can do this by following the directions in the manual. You can also check the torque requirements on the caliper bolts. For this motorcycle, the torque is 34Nm. You should also push the pistons back into the caliper to make room for the thicker material. To avoid piston problems, clean the pistons and apply red rubber grease.

Bestseller No. 1
WerdeReich Brake Caliper Compression Tool Disc Brake Pad Spreader Brake Caliper Tool Press, Universal Fit Compatible Brake Caliper Tool with Car Motorcycle
  • Auto Car Disc Brake Pad Spreader Separator Piston Auto Caliper Hand Tool, Essential tool for retracting the brake piston to allow insertion of new brake pads.
  • An essential tool for removal and installation of brake pads, Help push the brake caliper brake piston back squarely with no damage to the piston face.
  • Premium quality, chrome vanadium steel material, quenching treatment, higher hardness. Fine thread design for accurate adjustment. brake pad spreader caliper compression tool
  • Brake caliper tool press use Chemically blackened steel spreader plates. Fitted with tommy bar but can be used with 1/2" drive ratchet wrench or 0.83" spanner.
  • It is brake caliper compression tool easy to use and suitable for most vehicles, please pay attention to the dimensions, Professional and heavy duty tool car hand tool, suitable for private car owner and repair shops.
Bestseller No. 2
ATV Rear Brake Caliper, Rear Brake Caliper Assembly for Motorcycle 100-125CC Engine
  • Scope of application: This brake caliper rear fits for 100-125CC engine motorcycle.
  • Scope of application: This brake caliper rear fits for 100-125CC engine motorcycle.
  • Aluminum Alloy Material: brake caliper motorcycle is made of high quality aluminum alloy material, durable and high-temperature resistant.
  • Excellent performance:Fully assembled, including a set of brake pads pre-installed; Heavy duty design, stable characteristics and high reliability. Great aftermarket replacement part, direct replace the factory brake caliper.
  • Packaging & Easy Installation: Package includes 1 * Rear Brake Caliper. Easy installation, perfect match to your original motorcycle
Bestseller No. 3
OTC4743 Motorcycle Brake Caliper Spreader Tool
  • OTC's Brake Caliper Spreader quickly and easily retracts pistons on most caliper styles, making for a trouble free pad replacement process
  • Fits calipers designed for 1/4 inch thick brake rotors commonly found on motorcycles
  • For all front and some rear disc brakes
  • Range: 1/4 inch (5 mm) to 2-1/4 inches (58 mm)
  • In addition to motorcycles, this spreader will work for all automotive applications that fall within its 1/4 inch to 2-1/4 inch operating range
Bestseller No. 4
M MATI Front Brake Caliper Master Cylinder Hose Assembly for Honda Motorcycle CR125 CR250 CRF250 CRF450 45150-MEN-006 45510-KRN-305
  • Manufacturer Part # 45150-MEN-006 45510-KRN-305 Replacement Part# 45150-MKE-A71 45150-MEN-A51 45510-KCE-671 45510-MEN-J01 45510-KRN-A91
  • Fitment: Compatible with Honda Motorcycle ▶CR125R 2004-2007 ▶CR250R 2004-2007 ▶CRF250R 2004-2020 ▶CRF250RX 2019-2020 ▶CRF250X 2004-2017 ▶CRF450R 2004-2020 ▶CRF450RWE 2019-2020 ▶CRF450X 2005-2017
  • Feature: This is high quality OEM specifications front brake assembly. Easy install saving your time and your labour.
  • Service:If there is any product problem within 1 year, please contact us to solve it for you.We provide product service.
Bestseller No. 5
Black Ultima 4-piston Billet Aluminum Motorcycle Brake Caliper WITH PADS - Mounting Kits Also Available - Harley Chopper Bobber Cafe Racer
  • Upgrade your stock brakes with this stealth, lightweight and compact 4- Piston brake Caliper!
  • CNC machined from 6061 billet aluminum to eliminate flex and reduce weight then powder coated flat (matte) black.
  • Utilizes stainless steel pistons and anti-rattle springs for increased performance and excellent wear resistance. Brake pads slide freely on ground pins to prolong pad life. Comes with brake pads, ground pins, pin springs, washers and set screw.
  • Can be set-up for a front or rear brake application. Designed for use with DOT-5 brake fluid for optimum performance.
  • We have mounting kits available to fit many different Harley models. These calipers also work with Billet Proof brake hanger kits!
SaleBestseller No. 6
Motorcycle Rear Brake Caliper,Akozon Aluminum Alloy Rear Brake Caliper Assembly Replacement for Motorcycle 100-125CC Engine
  • Application : Rear brake pump The rear disc brake is suitable for 100-125cc engine motorcycles.Before purchasing, please make sure our products are compatible with your vehicle for fast use. for quad bremssattel for viper 150cc rear brake caliper
  • Application : Rear brake pump The rear disc brake is suitable for 100-125cc engine motorcycles.Before purchasing, please make sure our products are compatible with your vehicle for fast use. for quad bremssattel
  • Application : Rear brake pump The rear disc brake is suitable for 100-125cc engine motorcycles.Before purchasing, please make sure our products are compatible with your vehicle for fast use. for gy6 scooter brake 2 piston rear calipers
  • Quality material : The rear brake caliper assembly is made of high quality aluminum alloy material, with good weldability, high precision, super , sturdiness and strength at high temperatures. for jonway 125 cb 12 a bremssattel hinten for rear disc brake caliper moped
  • Professional manufacture : The rear brake caliper has been carefully designed and tested, and meets the highest quality control standards, rugged design, high sensitivity, high reliability, and stable performance. for swm 125 bremssattel for 125cc rear brake caliper
Bestseller No. 7
Motorbike Motorcycle Brake Caliper Piston Removal Tool Set Frozen Pistons
  • This tool has been designed to drastically reduce the time taken when dismantling motorcycle brakes with sliding calipers
  • Removes frozen pistons with ease.
  • The tool will not mark or damage the working part of the piston and will remove frozen pistons with ease.
  • Includes 12 universal adapters. Sizes 19,20,21,22,23,24,25,26,27,28,29,30mm.
Bestseller No. 8
M MATI Front Brake Caliper & Pads for Suzuki Motorcycle DR250 DR350 RM125 RM250 RMX250T 59300-08D00-999
  • Manufacturer Part # 59300-08D00-999 Replacement Part# 59300-27C11-999 59300-27C00
  • Fitment: Fit for Suzuki Motorcycle ▶DR250 1990-1995 ▶DR350 1990-1999 ▶RM125 1986-1995 ▶RM250 1986-1995 ▶RMX250T 1989-1996
  • Feature: Perfect aftermarket replacement of Suzuki brake caliper 59300-08D00-999. With brake pads, banjos, exact mounting bracket, direct install.
  • Package:A Brake Caliper W/Pads is packed in a fine box.
  • Service:If there is any product problem within 1 year, please contact us to solve it for you.We provide product service.
Bestseller No. 9
RCRBT Motorcycle Front Brake Caliper Assembly Compatible with Honda CRF125R 125F/FB 150F 230F 250F 450R ,XR250L 250R 400R 600R 650R,CR250R CR500R with Brake Pads
  • [Fitment] Compatible with Honda CR125R CR250R CR500R CRF125F/FB CRF150F CRF230F CRF250F CRF450R XR250L XR250R XR400R XR600R XR650R
  • [Material]This brake caliper is mechanically made of high-strength aluminum alloy material. The braking function is very sensitive, which can ensure your braking safety while driving.
  • [Advantage]This product is made of high-quality materials and mechanically manufactured. The product installation is very simple, and those who have experience in replacing and installing motorcycle calipers can install it by themselves. This product can be used as a replacement for motorcycle calipers. It is of high quality and can be purchased with confidence
  • [Remarks] This is aftermarket replacement item but not genuine.
  • Our products are 100% brand new. If you have any questions after you receive the goods, please contact us as soon as possible and we will solve them for you.
Bestseller No. 10
5Pcs Banjo Bolt, M10x1.25 Banjo Bolt Hard Iron Motorcycle Banjo Screws for Brake Caliper Master Cylinder
  • 【Non-slip Design】-- Comes with 5pcs Brake Banjo Bolts & 10 Washer. Neat threads, not easy to slip, safer to use
  • 【Durable & Sturdy】-- Made of high quality iron material, our banjo bolt washer is durable and sturdy, providing you with long use term
  • 【For Most Motorcycles】-- Our m10x1.25 banjo bolt fits for most motorcycles brake caliper, brake clutch master/slave cylinder and radiates energy hose
  • 【Specifications】-- Condition: 100% brand new, Material: iron, Color: army green, Size: shown as picture, Quantity: 5pcs bolts + 10 washers, Package Weight: approx.100g, Fitment: for brake caliper, brake clutch master/slave cylinder and radiates energy hose
  • 【2 Sizes】-- 2 standard size banjo fitting M10 x 1.25mm and M10 x 1.0mm for your option

Last update on 2022-05-12  / Images from Amazon Product Advertising API

About the author

Writer @ Motorcycleall.

Leave a Comment